Shows Low Batt:
on display when batteries needs to
be r eplaced. Use 6 Alkaline AA cells
Low Battery indication has 2 steps:
1)
LOW BATT CHANGE SOONLOW BATT CHANGE SOON
LOW BATT CHANGE SOONLOW BATT CHANGE SOON
LOW BATT CHANGE SOON
comes on when you have approx. 4 hours
left - plenty of time.
2)
LOW BATT LOW BATT
LOW BATT LOW BATT
LOW BATT
CHANGE NOWCHANGE NOW
CHANGE NOWCHANGE NOW
CHANGE NOW
comes when you have approx.
1/2 hour left.
NOTE: THIS MODEL DOES NOT USE
RECHARGABLE BATTERIES.
Power consumption is so low that
it only needs battery replacement about
once a year or less.
Low Battery in the wheel pads is indicated
by the flashing Green LED changing to
flashing Red. A steady Red LED indicates
batteries are too low to run the pads.
I
nstructions for Model No. 72710, 72711, 72724, 72725, 72755 Wireless Scales
• Control box shuts off after 1+ hour. Push
ON/OffON/Off
ON/OffON/Off
ON/Off and turn pads back on to resume operation
(DO NOT re-zero unless car is off pads)
• If you turn off just the control box after 1 minute pads go into "standby" mode. If control box is turned back
on within 1 hour pads will go back to active. If the green LED is out you will need to turn the pads back on also.
• Green LED on pad shows power. Flashing fast is normal operation. Slower flash indicates "standby"
mode waiting for control box to be turned back on. Red LED indicated low pad batteries.
• A pad not communicating with the control box is indicated by "- - -".
•
System can be set for Metric readout. See below.
• Keep the system clean and dry. Do not drop either the pads or the control box.
REMEMBER - there are electronics in the pads that could be damaged by rough handling.
• Store in a clean dry place. Keep away from static electricity.
Call, FAX, e-mail
if you have any questions or problems.
Memory:
To store weights in
Memory push
& hold
Memory Store
button, then push #1 - 8.
To recall push and hold
#1 - 8 only.
2/12
Zero:
Push BEFORE putting
car on scales.
DON'T push Zero
AFTER car is on scales.
This defines zero
weight.
"2ero" on display
indicates zero has been
lost. Remove weight &
rezero.
1) Set up pads along side car. Scale pads are marked RF, LR, etc. and must be used at that location.
2) Turn on each pad. Push Orange button or Rocker Switch on the side of the pad. The Green LED will start to flash.
3) Turn on control box. The control box will search and "find" the pads and weights will appear. This takes 5 - 10 seconds.
4) Push Zero.
This defines "0" weight. DON'T PUSH Zero AFTER CAR IS ON SCALES.
5) Lift car and place pads under wheels. "Shake" car up & down at each corner to settle out any shock or suspension friction.
Customize 4 line
display:
To change the 4 line % display to
your preference push CHANGE
DISPLAY and hold for 5 sec. Top
line will start to flash. Use arrows to
scroll up or down to the % you want
on that line. Push CONTINUE. The
second line starts to flash. Use
arrows to select this line. Press
CONTINUE after each selection.
Normal function resumes after last
selection or push ON. This will stay
until you change.
Longacre Racing Products, Inc.
16892 146
th
St SE, Monroe, Wa. 98272
Ph (360) 453 2030 FAX (360) 453 2031
www.longacreracing.com
To CHANGE BATTERIES:
Remove 4 small screws in the plate on the bottom of the black
enclosure - marked Batteries . Replace with 6 quality AA
alkaline batteries (always replace all batteries). Be sure
polarity is correct. The coil spring goes to negative end.
To CHANGE BATTERIES -
4 pads:
Remove 2 phillips head screws on the bottom of the pad on the opposite end to the transmitter - black box w. orange button.
you will see the battery holder just inside the pad, marked "BATTERY". Slide it out between the upper and lower platforms.
Remove the small silver screw on the black battery holder and slide the lid off. Replace with 3 quality AA alkaline batteries and
reinstall (always replace ALL batteries in a pad - recommend you change batteries in 4 pads) .
Metric:
See
below
This system works just like our wired scales. No complicated controls here. Everything is very simple.
CAPACITY:
Most #s listed: 1500 lb
(650 kgm) per pad.
#72755 kart scale: Do NOT
exceed 400 lbs.
(180 kgm)
Excess weight can damage
the load cells.
Control Box:
(1 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals